OPENCORES.ORG

What do you mean when you say you don't get a response?

You'll have to write these yourself or ask/pay somebody else to do it for
you.

Cheers,
Richard

-----Original Message-----
From: cores-bounces@o... [mailto:cores-bounces@o...] On
Behalf Of zhangming98@h...
Sent: Friday, July 22, 2005 9:45 PM
To: cores@o...
Subject: Re: [oc] I2C ip core integration for ALTERA FPGAs

Hi, Richard, 
Can you tell me how to code the driver of the wb I2C core attached to 
NiosII? 
Thanks!
Ming

----- Original Message ----- 
From: Richard Herveille<richard@h...> 
To: 
Date: Thu Jan 27 18:16:52 CET 2005 
Subject: [oc] I2C ip core integration for ALTERA FPGAs 

> What do you mean when you say you don't get a response? 
> Can you check that your writing into the regs correctly (check CYC, 
> STB). 
> The core should respond with an ACK. 
> Now if you're checking the scl and sda signals, make sure you 
> hooked up the 
> tri-state output correctly and you pulled-up the wires. 
> Otherwise the core won't work. 
> Cheers, 
> Richard 
> 
> > -----Original Message----- 
> > From: cores-bounces@o... 
> > [mailto:cores-bounces@o...] On Behalf Of 
> > David2565@h... 
> > Sent: Friday, January 21, 2005 4:34 PM 
> > To: cores@o... 
> > Subject: Re: [oc] I2C ip core integration for ALTERA FPGAs 
> > 
> > Hi, 
> > 
> > I tried to use this I2C core(the VHDL version) in a NIOS2 
> > system with quartus 2(4.1) I connected everything like stated 
> > below, but I get no response from it when I write to a 
> register. 
> > I did not connect the other end of the I2C chanel because I 
> > want to make sure it was connected properly. Could that be 
> > the problem? 
> > 
> > I used the following commands to try to send something: 
> > [code] 
> > IOWR_8DIRECT(I2C_BASE,OC_I2C_CR,IORD_8DIRECT(I2C_BASE, 
> > OC_I2C_CR)|OC_I2C_EN); //chip enable 
> > IOWR_8DIRECT(I2C_BASE,OC_I2C_PRER_LO,0x50);//set prescaler 
> > IOWR_8DIRECT(I2C_BASE,OC_I2C_PRER_HI,0x00); 
> > IOWR_8DIRECT(I2C_BASE,OC_I2C_TXR,0xAC);// set write adres 
> > IOWR_8DIRECT(I2C_BASE,OC_I2C_SR,(IORD_8DIRECT 
> > (I2C_BASE,OC_I2C_SR)|OC_I2C_STA|OC_I2C_WR));//set some 
other 
> > bits 
> printf("%x\n",IORD_8DIRECT(I2C_BASE,OC_I2C_SR));// check 
> (i get 
> > FF!?) 
> > while(IORD_8DIRECT(I2C_BASE,OC_I2C_SR)& OC_I2C_TIP); 
> > printf("%x\n",IORD_8DIRECT(I2C_BASE,OC_I2C_SR)); 
> > IOWR_8DIRECT(I2C_BASE,OC_I2C_TXR,0x5C); 
> > printf("%x\n",IORD_8DIRECT(I2C_BASE,OC_I2C_SR)); 
> > IOWR_8DIRECT(I2C_BASE,OC_I2C_SR,(IORD_8DIRECT 
> > (I2C_BASE,OC_I2C_SR)|OC_I2C_STO|OC_I2C_WR)); 
> > [/code] 
> > 
> > Hope someone can help, 
> > David 
> > 
> > 
> > ----- Original Message ----- 
> > From: c.scherp@3...<c.scherp@3...> 
> > To: 
> > Date: Thu Apr 15 16:20:50 CEST 2004 
> > Subject: [oc] I2C ip core integration for ALTERA FPGAs 
> > 
> > > Hallo Guido, 
> > > 
> > > it works ! Thank you very much for helping me ! 
> > > 
> > > Christian. 
> > > 
> > > Datum: 	Fri, 2 Apr 2004 14:22:33 +0200 
> > > Von: 	"Guido Kuhlmann" 
> > > <Guido.Kuhlmann@t...> 
> > > Betreff: 	RE: [oc] I2C ip core integration for 
> > > ALTERA FPGAs 
> > > An: 	"'Discussion list about free open source IP 
> > > cores'" <cores@o...> 
> > > Antwort an: 	Guido.Kuhlmann@t..., 
> > > 	Discussion list about free open source IP cores 
> <cores@o...> [ 
> > > Doppelklick auf diese Zeile zeigt Optionen für 
> Abo-Liste ] Hi 
> > > Christian, you can easily connect the I2C Wishbone core 
> to the NIOS 
> > > processor (I don't know the simple I2C core). 
> > > 1. Within SOPC builder, generate interface to user logic. 
> > > 2. Select bus interface type: avalon register slave. 
> > > 3. Add "i2c_master_top.v" design file. 
> > > 4. Read port list from file. 
> > > 5. Connect the signals as follow: 
> > > wb_adr_i <=> address 
> > > wb_dat_i <=> writedata 
> > > wb_dat_o <=> readdata 
> > > wb_we_i <=> write 
> > > wb_stb_i <=> chipselect 
> > > wb_cyc_i <=> chipselect 
> > > wb_inta_o <=> irq 
> > > wb_clk_i <=> clk 
> > > wb_ack_o <=> waitrequest_n 
> > > wb_rst_i <=> always0 
> > > arst_i <=> reset_n 
> > > scl_pad_i <=> export 
> > > scl_pad_o <=> export 
> > > scl_padoen_o <=> export 
> > > sda_pad_i <=> export 
> > > sda_pad_o <=> export 
> > > sda_padoen_o <=> export 
> > > 6. Under timing tab, leave the setup, wait and hold 
> settings at 0 
> > > cycles. > > You can now access the I2C core via 
> included "oc_i2c_master.h". > > Hope this helps. 
> > > Guido. > > 
> ______________________________________________________ > > 
> _______ > > Guido Kuhlmann > > Tigris Elektronik GmbH 
> http://www.tigris.de > > 
> ______________________________________________________ > > 
> _______ > > > -----Original Message----- > > > 
> From: cores-bounces@o... > > > 
> [mailto:cores-bounces@o...]On > > > Behalf Of 
> c.scherp@3... > > > Sent: Wednesday, March 31, 2004 10:31 
> AM > > > To: cores@o... > > > Subject: [oc] I2C 
> ip core integration for ALTERA FPGAs > > > > > > 
> > > > > > > I´m new to opencores.org and I 
> want to integrate a simple > > I2C > > > Bus Master 
> Interface > > > in an ALTERA Apex / Cyclone / Stratix 
> Device with > QuartusII and SOPC > > > Builder. I do 
> not need the complex wishbone version of > the I2C core. > 
> > I´m > > > happy with the simple > > > 
> I2C Bus Master which can be found in I2C.vhd. Is there any > 
> > > documentation available for this version ? Or can anyone 
> > give some > > > advice how to connect this core to 
> the ALTERA Avalon Bus and the > > > ALTERA Nios 
> Soft-Processor ? Thank > > you... > > > Christian. 
> > > > > > > > > > > > > 
> _______________________________________________ > > > 
> http://www.opencores.org/mailman/listinfo/cores > > > > 
> > _______________________________________________ > > 
> http://www.opencores.org/mailman/listinfo/cores > > -- > 
> > 3D Alliance GmbH > > Hauptstr. 46 > > 35649 
> Bischoffen > > Tel. 06444 / 93 19 - 0 Fax. 06444 / 93 19 - 12 
> > > > _______________________________________________ > 
> http://www.opencores.org/mailman/listinfo/cores > 
> 
_______________________________________________
http://www.opencores.org/mailman/listinfo/cores