|
Message
From: sip@d...
Date: Thu, 24 Apr 2003 13:16:55 -0100
Subject: Re: [openrisc] How to make ping work on or1ksim
Hi,
I have done as suggested, but it still does not work. I have noticed
that the sim.cfg file found in orp/..../uClinux-2.0.x has parameters
not supported be the lastest or1ksim. Does anyone know for sure that
the ping is still working with the newest simulator, and if so, how
shall the sim.cfg look like and which options must be enabled/disabled
(besides --enable-ethphy) when configuring/compiling the or1ksim.
Soeren
----- Original Message -----
From: youwenyi@a...
To: openrisc@o...
Date: Thu, 24 Apr 2003 07:21:20 -0100
Subject: Re: [openrisc] How to make ping work on or1ksim
>
>
> Hi,
>
> After I sent out the question on how to run ping on or1ksim, some
> people told me they have the same problem and asked me whether I
> have solved the problem. I have finally figured out how to do that.
> Here is how:
>
> 1. Use "--enable-ethphy" as option when "configure" or1ksim.
> 2. Assume your LAN subnet is 192.168.0.0/24. Go to or1k/romfs/etc,
> edit "rc" to be
> ifconfig eth0 inet 192.168.0.9 netmask 255.255.255.0 hw ether
> 00:11:22:33:44:55
> route add -net 192.168.0.0 netmask 255.255.255.0 dev eth0
> 3. Run genfomfs, and compile uCLinux.
> 4. Run or1ksim as root. (It took me a lot of time to figure this
> out! )
> 5. Run "ping 192.168.0.9", you should see loop-back reponse.
> 6. Assume another host on LAN is 192.168.0.1, run
> "ping 192.168.0.1". You should see ping reponse from that host.
>
>
> you-wen
>
>
> ----- Original Message -----
> From: You-Wen Yi <youwenyi@a... >
> To: openrisc@o... , youwenyi@a...
> Date: Sat, 08 Mar 2003 19:18:00 -0800
> Subject: [openrisc] How to make ping work on or1ksim
>
> >
> >
> > Hi,
> >
> > I compiled uClinux and or1ksim following intructions in
> > or1k/uclinux/uClinux-2.0.x/README.or32.
> > Basic unix commands like "ls" and "cd" work. But networking
> > commands
> > don't work.
> >
> > The /etc/rc executes
> > Command: ifconfig eth0 inet 10.1.1.200 netmask 255.0.0.0
> hw
> > ether
> > 00:01:02:03:04:05
> > Command: route add -net 10.0.0.0 netmask 255.0.0.0 dev
> eth0
> > when booting up the system. I don't see error messsage for
> these
> > two
> > commands.
> >
> > After that, if I do "ifconfig" to confirm network
> configuration, I
> > get
> > /proc/net/dev: No such file or directory
> >
> > If I do "route", I get
> > /proc/net/route: No such file or directory
> > INET (IPv4) not configured in this system.
> >
> > If I do "ping 192.168.0.1", I get
> > PING 192.168.0.1 (192.168.0.1): 56 data bytes
> > ping: sendto: Network is unreachable
> > ping: wrote 192.168.0.1 64 chars, ret=-1
> > ping: sendto: Network is unreachable
> > ....
> >
> > Can anybody tell me how to fix the problem?
> > I don't see directory /proc, should I add that directory to
> make
> > networking commands work?
> > Should I make the IP address and Ethernet MAC address to be
> same
> > as
> > those of
> > the host PC running or1ksim? Which file should I change?
> >
> > Thanks !
> >
> > You-Wen Yi
> >
>
|
 |
Browse
